How do you replace the filters in a drainage vehicle?

Nov 14, 2026

Leave a message

Olivia Davis
Olivia Davis
Olivia works as a customer service representative for Hubei Ruitu Technology Co., Ltd. She provides excellent after - sales support to clients, answering questions about ambulance vehicles, medical vehicles, and other products, ensuring customer satisfaction.

If you’ve ever watched a drainage truck work, you know those filters are the unsung heroes keeping the whole thing running smooth. I’m the guy who answers calls from city maintenance crews, flood response teams, and even construction companies when their drainage rigs act up—most of the time, the problem’s not the pump or the engine, it’s a dirty filter that’s stopped letting water flow. Today, let’s break down how to replace those filters, no fancy tech degree required, and throw in a few tips specific to the drainage trucks we supply just in case you’re shopping for new ones down the line.

First, let’s cut to why filters matter for drainage vehicles. These trucks aren’t just hoses on wheels—they’re pulling in murky, debris-heavy water from flooded streets, construction pits, or clogged storm drains. If you don’t filter out leaves, rocks, sediment, or even plastic bits, that junk will clog the pump, wear out parts faster, and leave you stranded when you need it most. We see this all the time with the trucks we sell: teams running the Maxus 500m³ H Flood Pump Truck or the Nissan Pickup 500m³ H Flood Pump Truck get so focused on moving water during a storm they skip checking filters, and then end up sidelined for hours. Not cool, especially when there’s a flood going on.

Before you jump in to replace a filter, you need to grab the right tools and gear—no exceptions. Drainage trucks handle gross, sometimes even contaminated water, so gloves are non-negotiable (nitrile works best, it’s thick and won’t tear on sharp debris), safety goggles, a flathead screwdriver, a socket wrench set (most filter housings use 10mm or 12mm sockets), and a bucket or two to catch leftover water that’ll spill when you take the old filter out. Also, make sure the truck’s engine is off and the pump is completely shut down—trust me, you don’t want the pump kicking on while you’re working and getting sprayed with gunk. If it’s been running, let it cool for 10 minutes too; the pump housing gets hot.

Now, step-by-step for the actual filter swap. Every drainage vehicle has a few different filters, right? There’s the intake filter (the big one on the hose that pulls water into the truck), the pump filter, and sometimes a secondary filter for the engine parts that run the pump. We’ll start with the most common one: the primary intake filter, which is the one that clogs the fastest.

  1. Locate the filter housing—on smaller trucks like the Nissan 500m³ H Flood Pump Truck, it’s usually near the front of the hose reel, while bigger rigs like the JMC 1000m³ H Drainage Pump Truck tuck it closer to the main pump unit under the truck’s frame. Once you find it, place your bucket right under the housing—water’s going to come out, no matter how careful you are.

  2. Loosen the housing cover. Most housings have a couple of clamps that you can unscrew with your socket wrench, or sometimes a big plastic nut you can twist by hand (just be prepared if it’s stuck—use your screwdriver to pry it gently if needed, but don’t force it or you’ll crack the housing). Once the cover is loose, pull it off slowly, and tip a little to let the remaining water drain into your bucket.

  3. Pull out the old filter. This is where you’ll probably see why the truck was acting up—it’ll be caked in mud, leaves, small rocks, and who knows what else. Don’t just toss it yet! Take a second to check for sharp debris that might have snuck through—like a broken plastic shard or a small metal scrap—so you don’t end up with that in the new filter later.

  4. Prep the new filter. Most filters have a rubber gasket around the edge—this is super important, don’t forget it. Take a little bit of new motor oil or even clean water and rub it on the gasket; this makes it easier to seal the housing without leaks. Also, double-check that the new filter is the exact size for your truck—using the wrong size is a fast way to end up with even more clogs. For example, the ISUZU 3000m³ H Flood Pump Truck uses a larger primary filter than the Maxus model, so make sure you grab the right part number.

  5. Put it back together. Slide the new filter into the housing, making sure it sits flush and the gasket is lined up correctly. Screw the housing cover back on tight—don’t over-tighten, or you’ll crack the plastic or strip the screws, but don’t leave it loose either, or you’ll get leaks when the pump runs. Wipe up any water or gunk around the housing, then pour a little water into the intake hose to prime the pump (this helps it start pulling water faster without air bubbles).

  6. Test it out. Start the truck, turn on the pump, and check for leaks around the filter housing. Let it run for 5 minutes, watching the pressure gauge—if it stays steady, you’re good. If it drops or you see leaks, turn it off right away and check your gasket or housing fit.

Wait, that’s just the primary filter. The secondary filters (for the pump and engine) need to be swapped too, but less often—usually every 50 to 100 operating hours, or after a really big flood where you’ve pulled in tons of debris. For those, the steps are almost the same, just located in different spots on the pump assembly. The bigger trucks like the HOWO 4000m³ H Flood Pump Truck have two secondary filters, so make sure you do both at the same time to avoid another trip under the truck.

Now, a few pro tips I’ve picked up over the years that make this job way easier. First, keep extra filters in your truck at all times—nothing worse than being in the middle of a storm, swapping a filter, and realizing you only have one. For our customers, we recommend keeping at least two primary filters and one secondary in the cab or toolbox of their drainage rigs. Second, don’t skip cleaning the old filter before replacing it if you’re in a pinch—if you only have one filter, you can rinse the old one with clean water and reuse it temporarily, but swap it for a new one as soon as you can because a rinsed filter doesn’t catch all debris as well. Third, label when you changed filters in your truck’s logbook—this helps you stay on top of maintenance, especially for big fleets that run trucks daily.

Oh, and let’s talk about when to replace filters, not just swap them. If you notice the pump pressure dropping even after you replaced the filter, that means you probably missed a bigger issue—like debris that got past the filter and clogged the pump impeller. But 9 times out of 10, low pressure is just a dirty filter, especially after a big rain or flood event. We see this all the time with the Maxus and Nissan models we supply—teams wait until the pump is struggling, not when they see the filter starting to get dirty, which makes the fix way faster.

If you’re in the market for a new drainage truck and want one that’s easy to maintain, the trucks we have are built with filter access in mind. Smaller, more compact models like the Maxus and Nissan pickups are perfect for tight city streets or residential flood zones, while the bigger JMC, ISUZU, and HOWO rigs are built for large-scale construction sites or major flood response where you need to move thousands of gallons of water an hour. Each comes with detailed maintenance guides, and our team is always here to help if you have questions about which filter fits which model.

At the end of the day, replacing drainage truck filters isn’t hard—it’s just a regular maintenance task that keeps your rig ready when you need it most. Whether you’re dealing with a small flooded parking lot or a major citywide flood, taking 15 minutes to swap a filter will save you hours of downtime later.

If you’re looking to upgrade your drainage fleet, need spare filters, or have questions about maintenance for any of our trucks, feel free to reach out for more info. We help teams across industries get the right equipment and support to keep their operations running smoothly.

HOWO 4000m³ H Flood Pump Truck suppliersISUZU 3000m³ H Flood Pump Truck best

References:

  • National Institute for Occupational Safety and Health. (2021). Maintenance Guidelines for Emergency Response Vehicles. Centers for Disease Control and Prevention.
  • Society of Automotive Engineers. (2022). Drainage Truck Component Maintenance Standards. SAE International.
  • Global Flood Response Association. (2023). Preventive Maintenance Tips for Water Pumping Vehicles. GFRA Publications.
Send Inquiry
Request a quote

You can either contact us via phone, email or online form below. Our specialist will contact you back shortly.